Home' Australian Automotive Aftermarket Magazine : Australian Automotive Aftermarket e-Zine - Sep 14 Contents PRODUCTS
22 AUTOMOTIVE AFTERMARKET MAGAZINE SEPTEMBER 2014
The EQP-115 Electronic EGR, Throttle Body, and
Actuator tester is one of the few testers available
that is capable of accurately driving both DC and
Pulsed Width Modulated (PWM) components on
today's complex vehicles, both on and off the
This versatile test unit is capable of driving
a variety of components, to quickly check for
complete movement or any seizing during
operation, and monitor the current draw
during all operating cycles on its integrated
digital read out.
Typical common vehicle components
that can be tested include electronic EGRs,
and position sensor monitoring during
actuator operation, and electronic throttle
bodies allowing for the integrated TPS unit to
be tested during the throttle body operation.
Due to its 0-40Amp delivery capability, the
EQP-115 can accurately drive actuators and
motors within that high current range.
The EQP-115 can also test the variable
intake manifold actuator and intake air control
(IAC) actuators (both on and off the vehicle), as
well as the supply pump and electric control
regulators for direct fuel injection and
common rail diesel systems. It also
handles EVAP control solenoids and HVAC blower motors (both on and
off the vehicle), as well as cooling fan testing at varying speeds and
other actuators and motors that
can be operated by PWM or DC within
the current range.
The EQP-028 Dynamic DC Volt Probe is a
high visibility, simple to use, one handed
dynamic voltage testing probe. It indicates
Power and Grounds and tests the circuit’s ability
to deliver current and identify loose, corroded or
broken wires. It allows the user to capture
intermittent spikes or drops in voltage, or take
voltage snapshots in any mode, any time.
The EQP-028 Dynamic DC Volt Probe tests
dynamic voltage drop and includes a glitch capture
mode. It operates in several modes including circuit
loading mode, testing the circuit's ability to delivery
current (voltage drop testing), and glitch capture mode, displaying
intermittent increase or decrease in voltage. It is also able to take
a voltage snapshot, or simply measure DC voltage in normal mode.
The EQP-028 Dynamic DC Volt Probe features red and green LEDs
to clearly identify power and ground, and is computer safe, suitable to
use on complex vehicle systems.
The PlusQuip range includes products for the professional technician
involved in the diagnosis and service of engine management systems.
PlusQuip products are workshop quality and all come with a 12 month
warranty and technical support.
For more information or to locate your local stockist visit
This new jack is due for release in mid-September 2014 at
Automechanika in Frankfurt. Calfinn Pty Ltd has secured limited stocks
that were scheduled to arrive for the launch date of September 1.
The new “77-model” has the lowest pick-up height offered on a
Compac jack of only 77 mm, as well as an extremely low chassis of 126
mm for better access to lifting points under low vehicles.
This new 1.5T-77 has been years in the making and has taken
countless hours of research into the crucial minimum heights required to
access the large range of makes and models of modern low vehicles in the
market, without compromising the strength and reliability of the jack.
The low chassis height of 126 mm is what sets this low profile jack
apart from the others on the market. While other models may be able to
offer a low minimum saddle height similar to the Compac 77 model, they
all have a chassis height of around 160mm which is approximately the
same height as any standard type of jack on the market. This prevents
these jacks from fitting far enough under many vehicles to get to the lifting
Although the chassis is a great new design, the hydraulic components
are 100 percent the same as all 1.5 tonne models that have been
available for decades. This means that a complete repair kit for the new
1.5 tonne 77 is exactly the same as for a Compac 1.5-tonne jack
manufactured way back in the 1960s.
The new 77-model features all the well-known advantages of Compac
jacks such as quick-approach foot pedal, safety lowering valve and powder
coated structure. The new 77-model is an excellent solution for workshops
intending to lift correctly according to the approved lifting points on
The three year factory warranty and long-life spare parts
availability makes this Compac jack a great investment.
To see this new model in action, scan in the QR code in
the article or go to Compac’s YouTube channel.
For further information, visit www.calfinn.com.au or call 02 9548 5350.
Calfinn introduces new Compac jack
Calfinn Pty Ltd is the first Compac dealer to introduce the lowest 1.5-tonne
trolley jack manufactured by Compac since they first started manufacturing
New PlusQuip Test Equipment
The PlusQuip range of workshop test equipment has recently expanded with the launch of several new
products including an Electronic EGR, Throttle Body and Actuator tester, and a Dynamic DC Volt Probe.
AM SEPT 2014 (e-zine):AM MAGAZINE SHELL 8/9/14 11:47 AM Page 22
Links Archive Australian Automotive Aftermarket e-Zine - Oct 14 Australian Auto Aftermarket e-Zine - August 14 Navigation Previous Page Next Page